Frames | No Frames
Return to Stylus Studio EDIFACT home page.|
Return to Stylus Studio EDIFACT D96B Messages page.
Permit expiration/clearance ready notice message
This specification provides the definition of the Permit expiration/clearance ready notice message (CODENO) to be used in Electronic Data Interchange (EDI) between trading partners involved in administration, commerce and transport.
1.1. Functional Definition
Notice specifying the cargo for which either the validity of the permits/Customs documents expires at short notice or for which regulatory Customs clearance has taken place.
This message is part of a total set of container-related messages. These messages serve to facilitate the intermodal handling of containers by streamlining the information exchange. The business scenario for the container messages is clarified in a separate document, called: 'Guide to the scenario of EDIFACT container messages'.
1.2. Field of Application
The Permit expiration/clearance ready notice message may be used for both national and international trade. It is based on universal commercial practice and is not dependent on the type of business or industry.
1.3. | Principles
Business area: Pre- and on-carriage transport of containers/equipment
Sending functions include: Container terminal, Inland terminal, Freight forwarder (including Non-Vessel Operating Common Carrier (NVOCC))
Receiving functions include: Shipping agent, Logistic Center, Freight forwarder
In the context of the 'Guide to the scenario of EDIFACT container messages' (as referred to at the start of section 1) the following guidelines, rules and functionality apply to this Permit expiration/clearance ready notice message:
See UNTDID, Part 4, Chapter 2.6 UN/ECE UNSM - General Introduction, Section 1.
3. TERMS AND DEFINITIONS
See UNTDID, Part 4, Chapter 2.6 UN/ECE UNSM - General Introduction, Section 2.
4. MESSAGE DEFINITION
4.1. Data Segment Clarification
This section should be read in conjunction with the Branching Diagram and the Segment Table which indicate mandatory, conditional and repeating requirements.
0010 UNH, Message header
A service segment starting and uniquely identifying a message. The message type code for the Permit expiration/clearance ready notice message is CODENO.
Note: Permit expiration/clearance ready notice messages conforming to this document must contain the following data in segment UNH, composite S009:
0020 | BGM, Beginning of message
A segment to indicate the beginning of a message and to transmit identifying number, and a further specification of the message type (in data element 1001: Document/message name, coded), such as Customs documents expiration notice, Customs clearance ready notice and message function.
0030 + DTM, Date/time/period
A segment to indicate a date and/or time applying to the whole message, such as date and time of document or message issue.
0040 FTX, Free text
A segment to specify free form or processable supplementary information, such as: - change information
A group of segments to specify a reference relating to the whole message, and its date and/or time.
0060 | RFF, Reference
A segment to express a reference which applies to the entire message, such as: - reference to previous message - container announcement reference (being the acceptance order reference number) - carrier's agent reference number
0070 + DTM, Date/time/period
A segment to indicate date and/or time related to the reference.
A group of segments to indicate details of the movement of containers.
0090 TDT, Details of transport
A segment to indicate information related to the main carriage stage of the transport (sea), such as carrier/liner service.
0100 LOC, Place/location identification
A segment to indicate a port corresponding to the transport stage, such as port of loading or discharge.
0110 DTM, Date/time/period
A segment to indicate a date/time relating to the transport details, such as arrival date/time.
A group of segments to identify a party and related contacts.
0130 | NAD, Name and address
A segment to identify the party's name, address, and function, such as: - message recipient - message sender - ordering customer - ordering customer agent - carrier agent (sea)
A group of segments to identify a contact and its communications related to the party.
0150 CTA, Contact information
A segment to identify a person or department for the party, such as: - information contact
0160 + COM, Communication contact
A segment to identify a communication number of a person or department to whom communication should be directed.
A group of segments to describe the goods items stuffed in containers.
0180 GID, Goods item details
A segment to identify a goods item stuffed in containers. A goods item can be identified by a goods item number.
A group of segments to specify documents and associated date(s) and time(s) for a goods item.
0200 DOC, Document/message details
A segment to specify a document prepared for a goods item.
0210 DTM, Date/time/period
A segment to associate issue and expiry date with the prepared document.
0220 SGP, Split goods placement
A segment to identify the containers in which goods are transported.
A group of segments to specify containers in which goods are transported.
0240 EQD, Equipment details
A segment to specify container prefix and number.
0250 RFF, Reference
A segment to specify the identifying number associated with a container, such as: - container sequence number
0260 NAD, Name and address
A segment to specify a pick-up address of Customs documents.
0270 CNT, Control total
A segment to specify the number of containers in the message, explicitly given by the sender.
0280 UNT, Message trailer
A service segment ending a message, giving the total number of segments in the message and the control reference number of the message.
4.2. Data segment index (Alphabetical sequence by tag)
4.3. Message structure
4.3.1. Segment table
Return to Stylus Studio EDIFACT D96B Messages page.