0. INTRODUCTION
1. SCOPE
   1. Functional definition
   2. Field of application
   3. Principles
2. REFERENCES
3. TERMS AND DEFINITIONS
4. MESSAGE DEFINITION
   1. Data segment clarification
   2. Data segment index (alphabetical sequence)
   3. Message structure
      1. Segment table

This specification provides the definition of the Advice on pending works message (CONAPW) to be used in Electronic Data Interchange (EDI) between trading partners involved in administration, commerce and transport.

The construction industry uses this message during its design, building and maintenance stages. It communicates with organisations about existing and planned services in the vicinity of the works.

Typically, this message is to enable a contractor who intends to start works to advise public authorities and water, gas, telephone, electricity ... distributors of his intention and to request them to send back plans or information under any form concerning existing networks.

The parties involved in such transfers belong to various industry sectors :

• the construction industry: contractors are often the originating parties of the message.
• gas, electricity, ... and more generally network distributors who are among the recipients of such messages, and who will process them to check whether they operate networks in an area concerned by works.
• public authorities, which may be
• clients or designers of projects
• in charge of specific responsibilities eventually

affected by the projects.

• in some cases, this type of advice may contain a legal status, the consequence of it may be the liability of the sender or receiver. Some insurance companies also may be concerned by this message.

Within the construction industry, there are numerous rules which govern this part of the process. Although, efforts have been made to keep the design of the message generic, other potential users of this message are cautioned about the specific and original role for which this message has been designed.

This is only one of a group of messages being designed for this flow among construction industry. Many aspects have to be considered, they are described in the following paragraphs. "Sending" process of the message : the message is originated by one party, but is sent to numerous recipients (from 10 to 20). This is the reason why an opportunity is given to use this message in conjunction with an appropriate service message wich enables the sender to indicate to a VAN operator that a considered message has to be distributed to more than one receiver. This message contains a request for information, to be provided back in another appropriate EDI message. The type of the information to convey in the "flow" CONAPW is not only alphanumeric, but some geographical and graphical information may be conveyed in conjunction with the advice itself, in order that the recipient gets all the relevant elements on the pending works. There is another appropriate EDI message being designed to convey information on plans and drawing organization, and it has been decided not to put this information in the message CONAPW itself, but to give an opportunity to link CONAPW with the drawing organization message. In addition, some recipients are interested in receiving the list of the other recipients. For the reason that this is not systematic, and in order to keep the design of the message as simple as possible, it has been decided to use an other appropriate service message providing a circulation list, and to give an opportunity to link CONAPW with this circulation message.

See UNTDID, Part 4, Chapter 2.6 UN/ECE UNSM - General Introduction, Section 1.

See UNTDID, Part 4, Chapter 2.6 UN/ECE UNSM - General Introduction, Section 2.

This section should be read in conjunction with the Branching Diagram and the Segment Table which indicate mandatory, conditional and repeating requirements.

0010 | UNH, Message header

A service segment starting and uniquely identifying a message. The message type code for the Advice on pending works message is CONAPW.

Note: Advice on pending works messages conforming to this document must contain the following data in segment UNH, composite S009:

0020 BGM, Beginning of message

A segment for unique identification of the Advice on Pending Works number and type of document.

0030 RFF, Reference

A segment to give prior references of the whole document, for example, project number or contract number, and authorization references if required.

0040 DTM, Date/time/period

A segment specifying the dates that apply, e.g. forecasted date to start works, duration of the project and/or forecasted date of end of the works.

0050 Segment Group 1: NAD-SG2

A group of segments identifying names, addresses and contacts relevant to the advice.

0060 NAD, Name and address

A segment identifying names and addresses and their function relevant for the whole advice on pending works. In the construction industry parties involved are e.g. the contractor, the designer, the client.

0070 Segment Group 2: CTA-COM

A group of segments giving contact details of the specific person or department within the party identified in the NAD segment.

0080 CTA, Contact information

A segment giving additional contact information relating to the party specified in the NAD segment, e.g. contact name, department or function.

0090 COM, Communication contact

A segment to identify a communication number of the previous information given in CTA (phone, fax, telex, etc.).

0100 LOC, Place/location identification

A segment, which enables the sender to specify in some occurrences the location(s) of the project.

0110 FTX, Free text

A segment to specify the nature of the works, in coded and/or clear form.

0120 DOC, Document/message details

A segment to specify which other documents (drawing organization, circulation list, plans, etc.) are to be sent and processed in conjunction with CONAPW, and what is the communication channel used to transfer them.

0130 CNT, Control total

A segment enabling controls, for example, the number of documents attached to CONAPW.

0140 AUT, Authentication result

A segment to provide an authentication of the message.

0150 UNT, Message trailer

A service segment ending a message, giving the total number of segments in the message and the control reference number of the message.